Search Engine

Search Results
Your search for 8Ω found the following documents (of 61488 documents searched):
Displaying documents 1-10 of 26, with best matches first:

1. GuitarAmp Forum - Re: amps and extension cabs - Wayne Parham, February 09, 2009 at 13:05:22

 If you have an external speaker cabinet rated 8Ω and an amplifier with a switch allowing you to set for 4Ω-8Ω, then...
URL: http://audioroundtable.com/GuitarAmp/messages/792.html

2. PiSpeakers Forum - Re: Thx Wayne. - Kim Schultz, April 27, 2005 at 18:53:09

I have a cheap driver from Monacor, but it models very closely to the Delta 10 when simulated in Hornresp. SP-10/100PA PA...
URL: http://audioroundtable.com/PiSpeakers/messages/16875.html

3. PiSpeakers Forum - Re: Thx Wayne. - Kim Schultz, April 27, 2005 at 18:53:09

I have a cheap driver from Monacor, but it models very closely to the Delta 10 when simulated in Hornresp. SP-10/100PA PA...
URL: http://audioroundtable.com/PiSpeakers/messages/16875.html

4. PiSpeakers Forum - Loudspeaker impedance curve - Zmax and tube amps - Wayne Parham, July 10,...

 If the amplifier has high damping factor (low output impedance), the impedance curve won't matter much. But amps with higher...
URL: http://audioroundtable.com/PiSpeakers/messages/22639.html

5. GuitarAmp Forum - Re: stereo cab help - Wayne Parham, November 14, 2008 at 16:03:50

 You can generally fudge the impedance a little bit, running 4Ω loads on 8Ω taps and vice versa. Just don't go too far with...
URL: http://audioroundtable.com/GuitarAmp/messages/779.html

6. PiSpeakers Forum - Re: Midhorn Flat Pack Kit??? - Wayne Parham, September 02, 2008 at 18:06:21

 The Delta 10A is 8Ω and the Delta 10B is 16Ω.
URL: http://audioroundtable.com/PiSpeakers/messages/22905.html

7. PiSpeakers Forum - Re: Studio One and Two Pi , anyone have an impedence curve chart for these? -...

They're a pretty easy load, two humps of about 15Ω each down low, then 8Ω up through the midrange, gradually rising up to...
URL: http://audioroundtable.com/PiSpeakers/messages/18579.html

8. SingleDriverSpeakers Forum - Re: Intercom replacement speaker needed - Wayne Parham, March 13,...

 I doubt the use of a 4Ω or 8Ω speaker will damage the amplifier in your intercom, so I'd just replace the 16Ω unit with...
URL: http://audioroundtable.com/SingleDriverSpeakers/messages/2229.html

9. Speaker Forum - Re: dummy impedance/power load to replace speaker being repaired? - Wayne...

 This is a a good part for substituting as a test/dummy load. It also works great for Zobels. 8Ω 100 watt non-inductive...
URL: http://audioroundtable.com/Speaker/messages/1256.html

10. ArraySpeakers Forum - Re: direct answer to Wayne - Wayne Parham, March 21, 2007 at 12:54:19

 I see, or at least I think I do. You're saying you want to double-check your wiring, right? If so, I'm not sure I can...
URL: http://audioroundtable.com/ArraySpeakers/messages/1534.html

Documents 1-10 of 26 displayed.

Results Pages: 1 | 2 | 3 | Next >>

Search Tips - Main Page